It Runs!!!! Bridgestone BS-7 Content Inside

I got my NOS piston, ring, and head gasket in the mail this morning from http://www.scramblercycle.com/. So of course I immediately had to get them fitted to the bike. I still wasn't having much luck getting it to start, so I pondered. The carb sits at quite an angle on this bike, so I thought I might need to raise the float level up a little. I ended up going a bit too far, as it leaked out the overflow tube. But at least I knew it had plenty of fuel.

So I gave it a kick:

It fired right up and idle on the choke. After a few seconds it came off the choke and revved clean. Hell yeah! I still need to fiddle with the float level, and then I can run it down the road.

Bridgestone BS/7 Pics

I dragged the Bridgestone to work today, so I could grab a few pictures at lunch. One of our old steam rooms had some nice lighting:

I actually found a new piston and rings from a supplier. I might get them in the mail today. If so, I could have a running BS-7 for the first time shortly!

Bridgestone BS-7: More Shots

Just a few shots of the BS7. This time with a smaller side panel, and a little badge. This was the original badge from the front headlight housing, and it fits on my custom built housing.

Badge:

Front view:

Bridgestone BS-7: Front Fender and Side Cover

I got a bit of work done this morning on the Bridgestone. Actually, the front fender has been a multiple day process, as I was having a hard time finding a fender that would work. As it happens, I had a spare Yamaha fender in the spares pile. It was a full fender style, but was heavily mangled. So I chopped it up, then made a mounting bracket for it out of aluminum. It got paint this morning.

Front fender mounted, with a nice little front brake cable guide attached to it:

Speaking of cables, I made up a front brake cable, throttle cable, and a clutch cable from spares. I cut everything to length, then soldered on new end pieces. Everything routes nicely around the new headlight fairing. Oh yeah, I made a headlight fairing! It is a very thin piece of aluminum from a spot light shield. I managed to cut and shape it into something decent looking. It uses a small Honda C100 headlight:

On the other side of the bike, I made up a simple side cover that covers up the battery. It also has a mount for the on/off ignition switch. I currently have it in a lightly polished aluminum. It might look better red. I'm not sure yet:

Another view of the front fender, headlight housing, and side cover:

C'

Bridgestone BS-7: Exhaust Finished

I got out this morning, before it got hot, and worked on the exhaust. I wrapped it with exhaust wrap, then built a little aluminum heat shield. Nothing too exciting, but i fun to shape the heat shield out of some scrap aluminum sheet.

I also fit a new carburetor Thursday evening, as the original was acting goofy after I cleaned it out. I had a spare 20mm Keihin carb, but it is a bit bigger in overall outside dimensions compared to the stock 15mm that came on the bike. I built a new intake manifold that was just a tick shorter, and angled up about 5-degrees. This allowed the carb body to clear the frame on top, and the engine case on bottom.

I'll likely see if I can kick it over tomorrow morning.

C'

Bridgestone BS-7: Exhaust Options

A couple options for the exhaust on the BS-7.

The stock setup, with the original chrome downpipe and muffler. It weighs 9 pounds, plus a pound for the rather robust mounting bracket, and is very much built for low-end performance. It also makes it harder to package the rear brake lever and footpeg.

Something I cobbled together over the weekend. It uses an old S90 muffler as the basis, cut into pieces and welded back up into the desired shape. It is built to give peak power a bit higher up (6,000rpm) in the range. It comes in at 4 pounds, and mounts to an existing hole in the frame. I plan on wrapping it in exhaust wrap, and building a small heat shield to keep my right leg from getting burned.

I prefer the high pipe, as it will make more power, and gives more clearance.

Bridgestone BS-7: Engine Assembly, Back in Frame

I spent some time out in the garage yesterday, cleaning up engine cases, stators, and the cylinder barrel and head. By the end of it, I had an assembled engine ready to go back in the bike. First thing this morning, I got the engine mounted up.

Fan side of engine:

I also got the read wheel assembly re-mounted. The bike didn't have the proper rear axle spacer when I got it, so I had to modify a Honda part to fit. The space needed to be cut down a tad shorter, so the wheel was centered side-to-side properly, so the sprocket would line up with the sprocket on the engine:

Clutch side:

C'

Bridgestone BS-7: Inside the Engine

In preperation for some engine case cleaning and polishing, I pulled the left side case cover off. This is the case that covers up the clutch. It also houses the clutch depresser thingy the clutch cable attaches too (it pivots and moves inward to release the clutch.) And, this is where you fill the engine with oil, and drain it. So I was expecting some amount of gunk buildup. this is what it looked like:

Inside of case:

Looking at the end of the clutch basket:

View from under the clutch basket, showing the drive gear:

I didn't clean anything. Not even a wipe of a rag, or a spray of degreaser. Everything looks great.

C'

Bridgestone BS-7: Rear Wheel

Yesterday was the front wheel, so naturally today was the rear wheel. Disassembled, cleaned, polished, repacked bearings and fit a fresh tire. then of course mounted on the bike for a few pictures:

Rear number, shown with gold pinstriping. My first shot at striping with my new brushes. I actually was decent at it:

I also outlined the red stripe on the tank and rear cowl"

It appears now that I need to start thinking about getting the engine mounted, so I can build an exhaust, run some cable, and make up some footpegs and a rear brake lever.

C'

Bridgestone BS-7: Front Wheel Rebuild

After some morning weed pulling, I decided to rebuild the front wheel on the Bridgestone. I dismounted the old crusty tire, disassembled the wheel, then proceeded to clean, paint, and polish. The front wheel bearings were in great shape, as were the seals. I also cleaned up the front brake shoes, pivot pins, and springs.

Lacing up the wheel. Always fun.

Truing up the rim. This is usually a pain in the ass, as you have to go back and forth on the spoke nipples to get things centered up, both with side-to-side run-out, and wheel balance.

Completed wheel, with fresh 2.5x17 IRC NR53 tire and tube mounted up. I gave the hub a very light polish, using 000 grade steel wool and oil. Then a very light rubbing of aluminum polish. The original rim polished up nice with some light chrome polish:

C'

Bridgestone BS-7: Stripes

I started the process of putting down some stripes on the tank and seat of the BS-7. A simple stripe over the top, that also ties in some of the shape of the tank:

C'

Bridgestone BS-7: Some Paint

I got a little paint on the BS-7 over the weekend, and did a quick mock-up this morning just to see how it looks. It is coming together. Now, time to pack for our Seattle and Victoria trip!

Bridgestone BS-7: Tank and Seat

Yes, more pics of the Bridgestone tank and seat. After a few days of filling, priming, sanding, priming etc. Almost ready for paint.

I have no idea why I used white primer for the seat, as it makes it difficult to see it in the photos:

I also found the Sport 90 bars fit a bit better than the stock BS-7 bars turned upside down. slightly narrower, and a bit more pullback:

C'

More seat stuff

Yep, more Bridgestone seat pics. This time of an actual completed part, somewhat trimmed to fit:

Pretty exciting, huh?

Bridgestone BS-7: Making a Seat

I missed a few photos during the process, but here is a quick recap.


I made a seat pan out of a 1/4" thick piece of pre-made fiberglass, courtesy a scrap piece of an anti-flotation flange from an AdvanTex AX20 pod (p00p cleaning box):


Another views, showing the front and rear mounting brackets. the front brackets pulls double duty, as the rear mount for the fuel tank:


I used foam crafting blocks glued above and below the seat pan. This is where I started shaping the foam with saws and sand paper, but failed to get any pics:


I managed to snap one photo of the seat with the first layer of fiberglass cloth applied, before I put on the rubber gloves and got covered in resin:


I've since stripped the form off the lower foam blocks, and have it sitting in the sun to fully cure. The rear hump has the foam encapsulated with cloth, so it should be fairly robust. In a few days I'll turn it over and add some fiberglass matting material to the lower side pieces, to give them a little thickness. Then I get to spend countless hours getting it smooth.

C'

More Bridgestone

Yes, another side view of the BS-7. This time, with a crudely crafted aluminum seat and tail section. Just to get an idea of how it looks, matched up with the tank:

I think the seat needs to be roughly 2-3" longer, as my butt will likely fit right on the seat above the rear shocks. But at least the look is coming together.

C'

Bridgestone BS-7: Tank Idea

The spare Bridgestone 90 Sport came with a fuel tank, which is an interesting shape not shared with the 90 Mountain and 90 Trail models. It is longer, lower, and somewhat pointy as shown below:

It happens to fit the BS-7 frame quite well, and extends backward about four inches more than the BS-7 tank. I think it could work with a cafe style seat. Oh, and a set of Honda Trail 70 rear shocks fit too, and are about 1/2" longer with a bit more stroke. I also like the exposed spring look.

C'

Bridgestone BS-7: Fiddling

So, what happens when a Bridgestone 90 sport front fork setup fits on a BS-7, with a little modification? This:

The stock BS-7 front fork setup is the older leading link style, with a pressed steal fork body. It happens to be severely mangled, so I either need to spend a weekend with some sheet metal and sheers, or find another front fork assembly. In the meantime, I wanted to see if this spare set of 90 Sport telescopic forks would fit.

I'm not sure why, but I'm losing interest in doing a "normal" restoration on this bike. I think it's because I'm already tired of cleaning old parts! And stripping paint, and sanding, and...you get the idea. Part of the fun of building something is to be able to take random spare parts and put them to use. In this case, I'm having visions of a replica 50cc racer. Something like these guys:

If I got his route, I'm going to have a goal of not modifying the frame or any of the BS-7 parts, that way if I ever decide to return it back to stock, I can. I'm thinking a custom tank, seat, and even a fairing. I know most of this stuff is available online, but it is all a bit expensive. So maybe I'll make the parts. Not sure how I'll make a fairing, but it could be a fun project.

C'

Bridgestone Frame - Primed

After getting the frame of the Bridgestone BS-7 stripped down, I managed to get it primed this afternoon:



I'll do a bit of light wet sanding, and get it painted in a few days.

C'